Crazy Machines Fanpage Board

Panda NC-Lab1
Seite 1 von 1

Autor:  Panda [ 30.11.2004, 10:56 ]
Betreff des Beitrags:  Panda NC-Lab1

Try the 10 very difficult space levels from my first laboratory for Crazy Machines - New Challenges. You're a pro if you master them. I hope you like it! :) My labs are mostly hard ones - so don't say I didn't warn you. ;) Please post your questions, etc. in this thread.
Note 1: panda-nc1-en.cml is the english version of panda-nh-lab1.cml
Note 2: New Challenges (NC) = Neue Herausforderungen (NH)

Download: panda-nc1-en.cml
CM-Fanpage: panda-nc1-en
Forum: german version

Autor:  Archn [ 04.02.2008, 02:03 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

Hi Can you explain how to do level 2 for me? I was unable to understand the German answer..

Obviously the switch connects to the gravity machine (That's 1 plug)

Then you place the C4 somewhere (Near the bottom right - I think)?

Then you obviously connect the C4 to the outlet (That's the other plug).

Then you only have a loose board and a seesaw...

Do you use either of these to set the gravity machine off?

And I'm trying to understand the objective.. The Robot on the right hits the anti gravity switch and goes to the left (flies there) and then he sets off the switch on the top left, and then that sets off the C4, which needs to set off the bombs in the bottom right? Is that it? If you can let me know that'd be great.. Thanks!

Edit: Nevermind I figured it out

Dateikommentar: Roboterror
lvl2.JPG [89.46 KiB]
34-mal heruntergeladen

Autor:  Archn [ 13.03.2008, 03:32 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

Couple screen shots

Can anyone help with lvl 9? Getting stuck...

lvl8.JPG [141.9 KiB]
27-mal heruntergeladen
lvl7b.JPG [152.78 KiB]
15-mal heruntergeladen
lvl7a.JPG [154.12 KiB]
15-mal heruntergeladen

Autor:  Archn [ 14.03.2008, 03:48 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

Still struggling a lot with lvl 9.. I think I have the concept, and am VERY close, but I just cannot seem to get it to finish.. Here is the screenshot of before I hit start and after I hit start..

Please tell me the solution.. Thanks

lvl11almostdone.JPG [137.75 KiB]
14-mal heruntergeladen
lvl11almoststarted.JPG [136.52 KiB]
11-mal heruntergeladen

Autor:  belab [ 14.03.2008, 08:20 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

uff .. i don't know.
you have to look with the editor or you can take the cheat to skip this level.
just type J+L+A in the leveloverview.

Autor:  Archn [ 15.03.2008, 02:13 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

Thanks.. I couldn't get any cheat to work, but I did manage to figure out how to view the solution in the editor.. I was way off.. the funny thing was after I solved it I clicked "Official Solution' and that solution didn't even work! :P

Autor:  belab [ 15.03.2008, 09:16 ]
Betreff des Beitrags:  Re: Panda NC-Lab1

oh ... in new challanges the cheat ist J+L+F10 ... sry

Seite 1 von 1 Alle Zeiten sind UTC + 1 Stunde
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group